Avaya P332GT-ML Installation And Configuration Manual Download Page 133

Page: 133 / 150

Avaya P332GT

-ML User’s Guide

119

Chapter 13

Embedded Web Manager

This chapter describes the installation procedures for the Embedded Web Manager
of the Avaya P330.

Overview

The Embedded Web Manager provides the following:
•

Managing and monitoring Power over Ethernet.

•

Device Configuration - Viewing and modifying the different device
configurations.

•

Virtual LANs - Viewing and editing Virtual LAN information.

•

Link Aggregation Groups (LAGs) - Viewing and editing LAG information.

•

Software Redundancy - Setting software redundancy for ports in an Avaya P330
Switch.

•

Port Mirroring - Setting up port mirroring for ports in an Avaya P330 Switch.

•

Trap Managers Configuration - Viewing and modifying the Trap Managers
Table.

•

Switch Connected Addresses - View devices connected to selected ports. Port
Security.

•

Intermodule Redundancy
— One pair per stack.
— Also operates as a result of a module fault, e.g., power failure.

System Requirements

Minimum hardware and Operating System requirements are:
•

One of the following operating systems:
— Windows® 95
— Windows 98 SP1
— Windows 98 OSR (Second Edition)
— Windows ME
— Windows NT® 4 Workstation or Server
— Windows 2000 Professional or Server

•

Pentium® II 400 Mhz-based computer with 256 Mb of RAM
(512 Mb recommended)

•

Minimum screen resolution of 1024 x 768 pixels

•

Sun Microsystems Java™ plug-in version 1.3.1

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands