Avaya P332GT-ML Installation And Configuration Manual Download Page 11 | Manualshive

Page: 11 / 150

background image

Avaya

P332GT

-ML User’s Guide

ix

Before you Install the P332GT-ML

Safety Information

Caution:

The Avaya P330 switch and modules contain components sensitive to

electrostatic discharge. Do not touch the circuit boards unless instructed to do so.

Caution:

Do not leave any slots open. Cover empty slots using the blanking plates

supplied.

Warning:

The fans are on whenever the power is on in the chassis.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Changes or modifications to this equipment not expressly approved by Avaya Inc.
could void the user’s authority to operate the equipment.

Conventions Used in the Documentation

Documentation for this product uses the following conventions to convey
instructions and information:

CLI Conventions

•

Mandatory keywords are in the

computer bold

font.

Preface

«
...
9
10
11
12
13
...
»

Summary of Contents for P332GT-ML























































































































































Reviews:

No comments

Related manuals for P332GT-ML

Brand: FANATEC Pages: 40

SwitchView SC8 DVI

Brand: Avocent Pages: 2

Brand: UNICOM Pages: 1

Brand: KCC Pages: 6

Brand: Icy Box Pages: 6

Brand: Thinklogical Pages: 27

ET2-0602-M Series

Brand: Leonton Pages: 17

Brand: TAXON TOOLS Pages: 9

Brand: Jerguson Pages: 4

kontron KSwitch D3 UM

Brand: S&T Pages: 38

Brand: MicroNet Pages: 123

DOMINION KX II DKX2-0E-E

Brand: Raritan Pages: 257

Brand: TP-Link Pages: 34

Brand: Kramer Pages: 4

Brand: Banner Pages: 8

5-Port Gigabit Switch 1000 Mbps

Brand: Hama Pages: 2

Brand: SmartThings Pages: 2

Brand: QNAP Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands