Avaya P332GT-ML Installation And Configuration Manual Download Page 134

Page: 134 / 150

Chapter 13

Embedded Web Manager

120

Avaya P332GT

-ML User’s Guide

•

Microsoft® Internet Explorer®

Netscape Navigator/Communicator® (see

table)

Note for users of Netscape Navigator:

The Java plug-in requires certain services from

Windows 95

which are not present if

Internet Explorer

is not installed. In order to

add these services to the operating system, please install Internet Explorer version 3
or higher. You can then use either browser to manage the switch.

Running the Embedded Web Manager

Note:

You should assign an IP address to the switch before beginning this procedure.

Open your browser.

Enter the url of the switch in the format

http://

aaa.bbb.ccc.ddd

where

aaa.bbb.ccc.ddd

is the IP address of the switch.

Note:

The user name is “root”

The default password for read-write access is “root”.

Note:

The Web management passwords are the same as those of the CLI. If you

have created additional CLI user names or changed the default passwords then you
can use those passwords for Web management as well.

Table 13.1

Embedded Web Manager/Browser Compatability

Windows 95 or NT

Windows 98, ME or 2000

Internet Explorer

5.0 or higher

5.01 or higher

Netscape Navigator/
Communicator

4.7

4.73

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands