Avaya P332GT-ML Installation And Configuration Manual Download Page 127

Page: 127 / 150

Chapter 12

Avaya P330 Layer 3 Features

Avaya P332GT

-ML User’s Guide

113

Policy Configuration CLI Commands

In order to...

Use the following command...

Set the default action for a given
Policy List.

ip access-default-action

Create an access-list rule in a
specific Access List.

ip access-list

Set the source list, destination list,
and destination module for copying
an entire Policy List

ip access-list-copy

Set the DSCP-to-COS mapping.
Based on range and action
parameters, system will apply
mapping to frames

ip access-list-dscp operation

Designates which original frame
fields influence internal queues
selection

ip access-list-dscp trust

Assign a name to a Policy List

ip access-list-name

Add the name of an owner to a
Policy List

ip access-list-owner

Delete an access-list element or a
Policy List

no ip access-list

Activate a Policy List

ip access-group

Deactivate a Policy List

no ip access-group

Display the DSCP to CoS map of a
policy-list

show ip access-list dscp

Set the list cookie for a specific
policy list

ip access-list-cookie

Display an access list

show ip access-list

Activate the “simulate” process for
a packet containing a specific field

ip simulate

Test the validity of a Policy List

validate-group

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands