Avaya P332GT-ML Installation And Configuration Manual Download Page 83

Page: 83 / 150

Chapter 11

Avaya P330 Layer 2 Features

Avaya P332GT

-ML User’s Guide

MAC Aging

Overview

The MAC Aging feature allows the user to configure a time interval after which
unused entries in the MAC Table will be deleted.

Configuring the P330 for MAC Aging

This section describes the configuration of the P330 for the MAC Aging
functionality.
•

MAC Aging is configured on the stack level.

•

MAC Aging can be globally enabled/disabled using the

set mac-aging

command.
— After firmware upgrade to version 4.0, MAC Aging default state is disabled.
— After NVRAM INIT, MAC Aging default state is enabled.

•

“mac-aging-time” is set in minutes:
— Default=5 minutes
— Minimum time=1 minute; maximum time= 3600 min

Note:

On a mixed P330/P330-ML stack, MAC Aging—if enabled—will apply only

to P330-ML modules in the stack.

MAC Aging CLI Commands

The following table contains a list of the CLI commands for the MAC Aging feature.
The rules of syntax and output examples are all set out in detail in the

P330 Reference

Guide

Table 11.4

MAC Aging CLI Commands

In order to...

Use the following command...

Enable/Disable MAC Aging

set mac-aging

Set the MAC aging time in minutes
(0=don’t age).

set mac-aging-time

Display the current status of the
MAC aging function

show mac-aging

Display the MAC aging time in
minutes.

show mac-aging-time

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands