Avaya P332GT-ML Installation And Configuration Manual Download Page 105

Page: 105 / 150

Chapter 12

Avaya P330 Layer 3 Features

Avaya P332GT

-ML User’s Guide

Enter the acquired Routing License Key into the P330-ML module using the

set license

CLI command.

set license

[module] [license] [featureName]

where:

module

- P330-ML module number (the location of the device in the

stack)

license

- license code

featureName

routing

and press Enter.

Reset the module.

Check that the license is activated using the CLI.
Use the

show license

CLI command.

License Key CLI Commands

In order to...

Use the following command...

Configure the feature license

set license

Display the feature license

show license

Display the switch identity
required for acquiring a license

show module-identity

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands