Avaya P332GT-ML Installation And Configuration Manual Download Page 137

Page: 137 / 150

Chapter 13

Embedded Web Manager

Avaya P332GT

-ML User’s Guide

123

Installing the Java Plug-in

If the network manager has configured the system, the plug-in should be installed
automatically.

Note:

Ensure that Java or JavaScript is enabled on your Web browser. Please refer to

your browser on-line help or documentation for further information.

If the plug-in is not installed automatically, then you have three options for
installing it manually:

Installing from the Avaya P330 Documentation and Utilities CD

Close all unnecessary applications on your PC.

Insert the “Avaya P330 Documentation and Utilities” CD into the CD drive.

Click

Start

on the task bar.

Select

Run

Type

\emweb-aux-files\plug-in_1_3_1.exe

where

is the CD

drive letter.

Follow the instructions on screen.

Install from the Avaya Site

Click on the link in the Welcome page.

Install from your Local Web Site

Click on the link in the Welcome page.

Note:

This option is only available if the network manager has placed the files on

the local Web server.

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands