Avaya P332GT-ML Installation And Configuration Manual Download Page 102

Page: 102 / 150

Chapter 12

Avaya P330 Layer 3 Features

Avaya P332GT

-ML User’s Guide

Note:

If the IP interface is on VLAN #1, continue with step 7.

Create the management/routing VLAN. Use the command

set vlan

<Vlan-id>

name

<Vlan-name>

replacing

<Vlan-id>

by the

VLAN number, and

<Vlan-name>

by the VLAN name. Press Enter.

Create an IP interface name. Type:

Router(configure)# interface <interface-name>

Press Enter.
The

Router(configure-if:<interface-name>)#

prompt appears.

Assign the IP address and network mask of the IP interface you have created.
Use the command

Router(configure-if:<interface-name>)# ip address

<ip-

address> <netmask>

Press Enter

Assign a vlan to the IP interface you have created. Type: Assign a vlan to the IP
interface you have created. Type:

Router(configure)# interface <interface-name># ip vlan

<vland-id>

Press Enter.

10 Type

exit

and press Enter. This returns you to the prompt:

Router(configure)#

11 If the management station is not on the same subnet as the switch, configure a

default gateway (static route). Use the command:

ip default-gateway

<ip-address>

and press Enter, replacing

<ip-address>

with the IP address of the default gateway.

12 Save the configuration changes by typing

copy running-config

startup-config

and press Enter.

Obtaining and Activating a License Key

In order to benefit from Layer 3 Routing functionality, it is required that you either
purchase a Layer 3 preconfigured P330-ML module or a Routing License Key
Certificate for the P330-ML.
Each Certificate is specific for:
•

The module type.

•

The required feature.

•

The number of devices.

After you purchase a Routing Licence Key Certificate, you must obtain and activate
a Routing License Key.

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands