manualshive.com logo in svg

Audi 2003 A8, Workshop Manual, Page: 3 / 252

Share
Download
Audi 2003 A8 Workshop Manual Download Page 3

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not 
 permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability 
     with respect to the correctness of information in this document. Copyright by AUDI AG.

Contents

00 - Technical data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1

Engine number   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1

2

Engine data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

3

Safety precautions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

3.1

Procedure before opening high-pressure section of injection system   . . . . . . . . . . . . . . . .

4

4

General repair instructions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

4.1

Rules for cleanliness when working on fuel supply system and injection system   . . . . . . . .

5

4.2

Checking for leaks in the fuel system   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

4.3

Foreign particles in engine   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

4.4

Contact corrosion!   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

4.5

Routing and attachment of pipes, hoses and wiring   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

4.6

Installing radiators and condensers   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

4.7

Checking vacuum system   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

10 - Removing and installing engine   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

1

Removing engine   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

2

Separating engine and gearbox   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3

Securing engine to engine and gearbox support   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4

Installing engine   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5

Assembly mountings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

5.1

Assembly mountings - exploded view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

5.2

Removing and installing engine mounting (left and right)   . . . . . . . . . . . . . . . . . . . . . . . . . . 46

5.3

Removing, installing and adjusting mounting for torque reaction support   . . . . . . . . . . . . . . 50

13 - Crankshaft group   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

1

Cylinder block (pulley end)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

1.1

Poly V-belt drive - exploded view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

1.2

Removing and installing poly V-belt   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

1.3

Removing and installing vibration damper   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

1.4

Renewing crankshaft oil seal (pulley end)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

2

Cylinder block (gearbox end)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

2.1

Drive plate - exploded view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

2.2

Removing and installing drive plate   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

2.3

Renewing crankshaft oil seal (gearbox end)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

3

Crankshaft   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

3.1

Crankshaft - exploded view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

3.2

Allocation of main bearing shells for new crankshaft   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

3.3

Allocation of main bearing shells on used and machined crankshafts   . . . . . . . . . . . . . . . . 70

3.4

Crankshaft dimensions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

3.5

Measuring axial clearance of crankshaft   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

3.6

Measuring radial clearance of crankshaft   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

4

Pistons and conrods   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

4.1

Pistons and conrods - exploded view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

4.2

Piston and cylinder dimensions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

4.3

Measuring radial clearance of conrods   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

15 - Cylinder head, valve gear   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

1

Chain drive   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

1.1

Timing chain covers - exploded view   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

1.2

Removing and installing timing chain covers (left and right)   . . . . . . . . . . . . . . . . . . . . . . . . 78

1.3

Removing and installing timing chain cover (bottom)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Audi A8 2003 ➤

10-cylinder direct petrol injection engine (5.2 ltr. 4-valve), mechanics - Edition 10.2013

Contents    

i

Summary of Contents for 2003 A8





























































































































































































































































Reviews:

No comments