manualshive.com logo in svg

Audi 2003 A8, Workshop Manual, Page: 42 / 252

Share
Download
Audi 2003 A8 Workshop Manual Download Page 42

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not 
 permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability 
     with respect to the correctness of information in this document. Copyright by AUDI AG.

3

Securing engine to engine and gearbox support

Special tools and workshop

equipment required
♦ Lifting tackle - 3033-
♦ Engine and gearbox sup‐

port - VAS 6095- with

bracket -VAS 6095/1-7-

♦ Workshop hoist -

VAS 6100-

♦ Lift arm extension (work‐

shop hoist) - VAS 6101-

Procedure
– Unplug electrical connector -arrow- at engine mounting (left-

side).

– Remove bolts -1 ... 4- and detach engine support with engine

mounting.

Audi A8 2003 ➤

10-cylinder direct petrol injection engine (5.2 ltr. 4-valve), mechanics - Edition 10.2013

36

     Rep. gr.10 - Removing and installing engine

Summary of Contents for 2003 A8





























































































































































































































































Reviews:

No comments