Home
/
Audi
/
2003 A8
/
Workshop Manual

Audi 2003 A8, Workshop Manual, Page: 115 / 252

Share

Page: 115 / 252

Audi 2003 A8 Workshop Manual Download Page 115

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

♦ Thrust piece - T40192-

♦ Oil seal extractor -T40195-

Procedure
• Engine removed and in position on scissor-type assembly

platform - VAS 6131 A- with gearbox attached.

– Remove air conditioner compressor ⇒ Rep. gr. 87 .
– Detach hose clip on dust cap -arrow- for air conditioner com‐

pressor drive.

– Pull off dust cap together with drive shaft for air conditioner

compressor from stub shaft of spur gear for air conditioner

compressor drive.

– Screw spindle of oil seal extractor -T40195- all the way out.
– Lubricate threaded head of oil seal extractor, place it in posi‐

tion and screw it into oil seal as far as possible (applying firm

pressure).

– Turn inner part of oil seal extractor against spur gear drive until

the oil seal is pulled out.

Note

If the sections of the oil seal come apart, apply oil seal extractor

again and pull out remaining part of oil seal.

– Clamp hexagon flats of oil seal extractor in vice and use pliers

to remove oil seal.

– Clean contact surface and sealing surface.

Audi A8 2003 ➤

10-cylinder direct petrol injection engine (5.2 ltr. 4-valve), mechanics - Edition 10.2013

1. Chain drive

109

«
...
113
114
115
116
117
...
»

Summary of Contents for 2003 A8





























































































































































































































































Reviews:

No comments