Home
/
Audi
/
2003 A8
/
Workshop Manual

Audi 2003 A8, Workshop Manual, Page: 236 / 252

Share

Page: 236 / 252

Audi 2003 A8 Workshop Manual Download Page 236

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

– Fit clamps so that ends of bolts do not protrude beyond bottom

of clamp.

• Bolt connections face one another.
– Align exhaust system so it is free of stress

1.3

Removing and installing exhaust pipes

(left-side)

Removing
• Engine removed and in position on scissor-type assembly

platform - VAS 6131 A- with gearbox attached.

Note

♦

Fit all heat shields and heat insulation sleeves in the original

positions when installing.

♦

All cable ties which are released or cut open when removing

must be fitted in the same position when installing.

– Take electrical connector -1- for Lambda probe 3 after catalytic

converter - G287- out of bracket and unplug it.

Note

Ignore items marked -2- and -arrows-.

– Remove bracket for electrical connectors -1 ... 4- for Lambda

probes from subframe -arrow-.

– Take electrical connectors -1- for Lambda probe 4 after cata‐

lytic converter - G288- and -2- for Lambda probe 3 - G285-

(before catalytic converter) out of bracket on gearbox and

unplug.

Audi A8 2003 ➤

10-cylinder direct petrol injection engine (5.2 ltr. 4-valve), mechanics - Edition 10.2013

230

Rep. gr.26 - Exhaust system

«
...
234
235
236
237
238
...
»

Summary of Contents for 2003 A8





























































































































































































































































Reviews:

No comments