ARTERY AT32F421 Series Reference Manual Download Page 49 | Manualshive

Page: 49 / 337

background image

AT32F421

Series Reference Manual

2022.11.11

Page 49

Rev 2.02

4.3.1

Clock control register (CRM_CTRL)

No-wait states, accessible by bytes, half-words or words.

Bit

Name

Reset value

Type

Description

Bit 31: 26

Reserved

0x00

resd

Kept at its default value.

Bit 25

PLLSTBL

0x0

ro

PLL clock stable
This bit is set by hardware after PLL is ready.
0: PLL clock is not ready.
1: PLL clock is ready.

Bit 24

PLLEN

0x0

rw

PLL enable
This bit is set and cleared by software. It can also be
cleared by hardware when entering Standby or
Deepsleep mode. When the PLL clock is used as the
system clock, this bit cannot be cleared.
0: PLL is OFF
1: PLL is ON.

Bit 23: 20

Reserved

0x0

resd

Kept at its default value.

Bit 19

CFDEN

0x0

rw

Clock failure detector enable
0: OFF
1: ON

Bit 18

HEXTBYPS

0x0

rw

High speed external crystal bypass
This bit can be written only if the HEXT is disabled.
0: OFF
1: ON

Bit 17

HEXTSTBL

0x0

ro

High speed external crystal stable
This bit is set by hardware after HEXT becomes stable.
0: HEXT is not ready.
1: HEXT is ready.

Bit 16

HEXTEN

0x0

rw

High speed external crystal enable
This bit is set and cleared by software. It can also be
cleared by hardware when entering Standby or
Deepsleep mode. When the HEXT clock is used as the
system clock, this bit cannot be cleared
0: OFF.
1: ON

Bit 15: 8

HICKCAL

0xXX

rw

High speed internal clock calibration
The default value of this field is the initial factory
calibration value.
When the HICK output frequency is 48 MHz, it needs
adjust 240 kHz (design value) based on this frequency for
each HICKCAL value change; when HICK output
frequency is 8 MHz (design value), it needs adjust 40 kHz
based on this frequency for each HICKCAL value change.
Note: This bit can be written only if the HICKCAL_KEY[7:
0] is set as 0x5A.

Bit 7: 2

HICKTRIM

0x20

rw

High speed internal clock trimming
These bits work with the HICKCAL[7: 0] to determine the
HICK oscillator frequency. The default value is 32, which
can trim the HICK to be ±1%.

Bit 1

HICKSTBL

0x1

ro

High speed internal clock stable
This bit is set by hardware after the HICK is ready.
0: Not ready
1: Ready

Bit 0

HICKEN

0x1

rw

High speed internal clock enable
This bit is set and cleared by software. It can also be set
by hardware when exiting Standby or Deepsleep mode.
When a HEXT clock failure occurs. This bit can also be
set. When the HICK is used as the system clock, this bit
cannot be cleared.
0: Disabled
1: Enabled

«
...
47
48
49
50
51
...
»

Summary of Contents for AT32F421 Series


















































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F421 Series

Brand: TC Electronic Pages: 2

Brand: Hal Communications Pages: 25

Brand: Roland Pages: 12

Momentum ROG Strix X570-E D-RGB

Brand: EK-Quantum Pages: 10

Brand: Tektronix Pages: 178

Brand: Juniper Pages: 7

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

Brand: ICP DAS USA Pages: 62

HHM Series HHM2245SA1

Brand: TDK Pages: 2

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Brand: IBM Pages: 74

Brand: SilverStone Pages: 2

Brand: Matrix Switch Corporation Pages: 48

Brand: Xilinx Pages: 36

Brand: Enterasys Pages: 5

Brand: Arctic Pages: 7

NexXxoS GPX-N 970 M03

Brand: Alphacool Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands