ARTERY AT32F421 Series Reference Manual Download Page 249 | Manualshive

Page: 249 / 337

background image

AT32F421

Series Reference Manual

2022.11.11

Page 249

Rev 2.02

HALL even: CxEN, CxCEN and CxOCTRL are updated.

Bit 4: 2

Reserved

0x0

resd

Kept at its default value.

Bit 1

C1IF

0x0

rw0c

Channel 1 interrupt flag
If the channel 1 is configured as input mode:
This bit is set by hardware on a capture event. It is
cleared by software or read access to the TMRx_C1DT
0: No capture event occurs
1: Capture event is generated
If the channel 1 is configured as output mode:
This bit is set by hardware on a compare event. It is
cleared by software.
0: No compare event occurs
1: Compare event is generated

Bit 0

OVFIF

0x0

rw0c

Overflow interrupt flag
This  bit  is  set  by  hardware  on  an  overflow  event.  It  is
cleared by software.
0: No overflow event occurs
1:  Overflow  event  is  generated.  If  OVFEN=0  and
OVFS=0 in the TMRx_CTRL1 register:
−      An overflow event is generated when  OVFG= 1 in
the TMRx_SWEVE register;
−      An  overflow  event  is  generated  when  the  counter
CVAL is reinitialized by a trigger event.

14.5.4.5 TMR16 and TMR17 software event register (TMRx_SWEVT)

Bit

Register

Reset value

Type

Description

Bit 15: 8

Reserved

0x0

resd

Kept at its default value.

Bit 7

BRKSWTR

0x0

wo

Brake event triggered by software
This bit is set by software to generate a brake event.
0: No effect
1: Generate a brake event.

Bit 6

Reserved

0x0

resd

Kept at its default value.

Bit 5

HALLSWTR

0x0

wo

HALL event triggered by software
This bit is set by software to generate a HALL event.
0: No effect
1: Generate a HALL event.
Note: This bit acts only on channels that have
complementary output.

Bit 4: 2

Reserved

0x0

resd

Kept at its default value.

Bit 1

C1SWTR

0x0

wo

Channel 1 event triggered by software
This bit is set by software to generate a channel 1 event.
0: No effect
1: Generate a channel 1 event.

Bit 0

OVFSWTR

0x0

wo

Overflow event triggered by software
This bit is set by software to generate an overflow event.
0: No effect
1: Generate an overflow event.

14.5.4.6 TMR16 and TMR17 channel mode register1 (TMRx _CM1)

The channel can be used in input (capture mode) or output (compare mode). The direction of a channel
is defined by the corresponding CxC bits. All the other bits of this register have different functions in input
and output modes. The CxOx describes its function in output mode when the channel is in output mode,
while the CxIx describes its function in output mode when the channel is in input mode. Attention must
be given to the fact that the same bit can have different functions in input mode and output mode.

Output compare mode:

Bit

Register

Reset value

Type

Description

Bit 15: 8

Reserved

0x0

resd

Kept at its default value.

Bit 7

C1OSEN

0x0

rw

Channel 1 output switch enable
0: C1ORAW is not affected by EXT input.
1: Once a high level is detect on EXT input, clear
C1ORAW.

Bit 6: 4

C1OCTRL

0x0

rw

Channel 1 output control

«
...
247
248
249
250
251
...
»

Summary of Contents for AT32F421 Series


















































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F421 Series

Brand: Jabra Pages: 15

Brand: Quatech Pages: 27

SAFETank Series

Brand: Raidon Pages: 49

Brand: Datasat Pages: 170

Brand: 3Com Pages: 16

Brand: Hama Pages: 6

Brand: ebm-papst Pages: 11

Brand: ZKTeco Pages: 68

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: IEI Technology Pages: 2

Brand: Xantech Pages: 5

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brand: ADTRAN Pages: 2

Brand: Aim Pages: 35

EZ-KIT LITE ADSP-2191

Brand: Analog Devices Pages: 98

Brand: IEI Technology Pages: 116

Brand: ADLINK Technology Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands