ARTERY AT32F421 Series Reference Manual Download Page 146 | Manualshive

Page: 146 / 337

background image

AT32F421

Series Reference Manual

2022.11.11

Page 146

Rev 2.02

1: Interrupt is enabled.

Bit 6

TDCIEN

0x0

rw

TDC interrupt enable
0: Interrupt is disabled.
1: Interrupt is enabled.

Bit 5

RDBFIEN

0x0

rw

RDBF interrupt enable
0: Interrupt is disabled.
1: Interrupt is enabled.

Bit 4

IDLEIEN

0x0

rw

IDLE interrupt enable
0: Interrupt is disabled.
1: Interrupt is enabled.

Bit 3

TEN

0x0

rw

Transmitter enable
This bit enables the transmitter.
0: Transmitter is disabled.
1: Transmitter is enabled.

Bit 2

REN

0x0

rw

Receiver enable
This bit enables the receiver.
0: Receiver is disabled.
1: Receiver is enabled.

Bit 1

RM

0x0

rw

Receiver mute
This bit determines if the receiver is in mute mode or not.
It is set or cleared by software. When the idle line is used
to wake up from mute mode, this bit is cleared by
hardware after wake up. When the address match is used
to wake up from mute mode, it is cleared by hardware
after wake up. When address mismatches, this bit is set
by hardware to enter mute mode again.
0: Receiver is in active mode.
1: Receiver is in mute mode.

Bit 0

SBF

0x0

rw

Send brake frame
This bit is used to send a  brake frame.  It can be set or
cleared  by  software.  Generally  speaking,  it  is  set  by
software  and  cleared  by  hardware  at  the  end  of  brake
frame transmission.
0: No brake frame is transmitted.
1: Brake frame is transmitted.

12.12.5 Control register2 (USART_CTRL2)

Bit

Register

Reset value

Type

Description

Bit 31: 16 Reserved

0x00000

resd

Forced 0 by hardware.

Bit 15

TRPSWAP

0x0

rw

Transmit/receive pin swap
0: Transmit/receive pin swap disabled
1: Transmit/receive pin swap enabled

Bit 14

LINEN

0x0

rw

LIN mode enable
0: LIN mode is disabled.
1: LIN mode is enabled.

Bit 13: 12 STOPBN

0x0

rw

STOP bit num
These bits are used to program the number of stop bits.
00: 1 stop bit
01: 0.5 stop bit
10: 2 stop bits
11: 1.5 stop bits

Bit 11

CLKEN

0x0

rw

Clock enable
This bit is used to enable the clock pin for synchronous
mode or Smartcard mode.
0: Clock is disabled.

«
...
144
145
146
147
148
...
»

Summary of Contents for AT32F421 Series


















































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F421 Series

FrameSaver 9120

Brand: Paradyne Pages: 2

eXtremeRAID 1100

Brand: Mylex Pages: 74

AAA-130SA SERIES

Brand: Adaptec Pages: 94

Brand: Sangoma Pages: 6

Brand: PMD Pages: 74

Brand: Paradyne Pages: 6

Brand: EZCast Pages: 24

Brand: WiebeTech Pages: 8

ServCon FPS-3003

Brand: LevelOne Pages: 45

System 4 Landmark Technic Processor

Brand: Ametek Land Pages: 34

X-NUCLEO-GFX01M Series

Brand: ST Pages: 31

OPTI495XLC VL-BUS 3/486

Brand: A-Trend Pages: 16

Brand: Idex Pages: 4

Firebox T85-PoE

Brand: Watchguard Pages: 27

BreezeACCESS II

Brand: Alvarion Pages: 324

Scalable Multi-Graphic Videowall Processors MGP 464W Series

Brand: Extron electronics Pages: 2

Brand: Lenze Pages: 29

Brand: AJA Pages: 129

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands