Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 4

Page: 4 / 105

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected]

Page 4 of 105

TABLE OF CONTENTS

HOW TO USE THIS MANUAL -------------------------------------------------------------------- 3

TABLE OF CONTENTS ---------------------------------------------------------------------------- 4

WARNINGS AND SAFETY INFORMATION -------------------------------------------------- 6

PACKING AND SHIPPING INSTRUCTIONS ------------------------------------------------- 9

INTRODUCTION ------------------------------------------------------------------------------------ 11

5.1.

Hardware ..................................................................................................... 12

5.2.

Instrument Models ........................................................................................ 13

5.3.

Oven ............................................................................................................ 13

5.4.

Inventory & Accessories ............................................................................... 14

INSTRUMENT SETUP ----------------------------------------------------------------------------- 15

6.1.

Instrument Location ...................................................................................... 15

6.2.

Interior of Test Chamber & Pan Support ...................................................... 16

6.3.

AC Power Connection .................................................................................. 16

6.4.

User Interface Operation .............................................................................. 18

6.5.

Contrast Adjustment ..................................................................................... 19

6.6.

Back Panel Connections .............................................................................. 20

6.7.

Connecting a USB Printer ............................................................................ 21

6.8.

Connecting a USB Drive .............................................................................. 22

6.9.

Connecting a Computer ............................................................................... 22

6.9.1

USB Driver Setup ............................................................................ 23

6.10.

Connecting a USB Keyboard ....................................................................... 28

6.11.

Installing the Nitrogen Purge Kit ................................................................... 28

6.12.

Nitrogen Control Module .............................................................................. 30

6.13.

Bar Code Reader ......................................................................................... 32

6.14.

Installing & Removing the External Filter ..................................................... 33

MOISTURE ANALYSIS TESTING -------------------------------------------------------------- 34

7.1.

Performing a Test ......................................................................................... 36

7.2.

Preparing Granular and Powdery Samples .................................................. 39

7.3.

Preparing and Testing Liquid Samples ........................................................ 39

MAIN MENU ------------------------------------------------------------------------------------------ 40

8.1.

Test Programs.............................................................................................. 41

8.1.1

Sample Name ................................................................................. 43

8.1.2

Temperatures .................................................................................. 44

8.1.3

Ending Criteria ................................................................................ 46

8.1.4

Sample Size Options ....................................................................... 47

8.1.5

Tare Options ................................................................................... 49

8.1.6

Result Display Options .................................................................... 51

8.1.7

Lift Compensation ........................................................................... 53

8.1.8

Linked Test Options ........................................................................ 54

8.2.

Test Results ................................................................................................. 55

8.2.1

Graph .............................................................................................. 57

8.3.

Calibration Menu .......................................................................................... 58

8.3.1

Balance Calibration Menu ............................................................... 58

8.3.1.A

View Calibration Report ...................................................... 59

8.3.1.B

Perform Span Calibration ................................................... 60

8.3.1.C

Linearity Verification Setup ................................................. 61

8.3.1.D

Perform Linearity Verification ............................................. 62

8.3.1.E

Span Calibration Reminder Setup ...................................... 63

8.3.2

Temperature Calibration .................................................................. 63

Summary of Contents for COMPUTRAC MAX 4000










































































































Search results

Summary of Contents for COMPUTRAC MAX 4000

Reviews:

Brands by name

Popular brands

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Search results

Summary of Contents for COMPUTRAC MAX 4000

Reviews:

Brands by name

Popular brands