Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 2

Page: 2 / 105

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected]

Page 2 of 105

Computrac

MAX

4000 / 4000XL

PROPRIETARY RIGHTS NOTICE

This manual contains valuable information developed by Arizona Instrument LLC for use

with the Computrac

line of moisture analyzers. No part of this manual can be

reproduced or transmitted in any form or by any means, electronic, mechanical, or

otherwise. This includes photocopying and recording or in connection with any

information storage or retrieval system without the express written permission of

Arizona Instrument LLC.



PLEASE NOTE:

There are 2 different instrument models in the MAX

4000 series: the

MAX

4000 and the MAX

4000XL, and features vary between the two models.

Throughout this manual, MAX

4000 is used to refer to both the MAX

4000 and the

MAX

4000XL when describing common features or functionality. When there are

specific differences between the two models, these are indicated through the usage of
MAX

4000XL for features that are only available in the MAX

4000XL. Refer to the chart

on page

for details regarding the feature differences between the models.

Summary of Contents for COMPUTRAC MAX 4000










































































































Search results

Summary of Contents for COMPUTRAC MAX 4000

Reviews:

Brands by name

Popular brands

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Search results

Summary of Contents for COMPUTRAC MAX 4000

Reviews:

Brands by name

Popular brands