manualshive.com logo in svg

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Share
Download
Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 17

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected] 

Page 17 of 105 

 

For best results, AZI recommends that the instrument is provided 
with its own 

DEDICATED

 electrical power outlet.  Do not put it on a 

circuit with motors, blenders, heaters, coolers, grinders, or other high 
current electrical devices.  
 
The power source outlet that is used by the MAX

®

 4000 

MUST BE 

GROUNDED

.  (If you are not sure if the socket is grounded, check 

with your plant electrician before proceeding).  

The MAX

®

 4000 will 

appear to function correctly even if the socket is not grounded, 
but there is a danger of possible electrocution!  If grounded 
outlets are not available, consider using a ground fault 
interrupter to protect personnel against electrical shock.

 

 

•

  Plug the power cord into a dedicated electrical power outlet.  Line noise on the power 

lines may affect accuracy.  A dedicated AC power line or an isolation transformer for 
the MAX

®

 4000 may be beneficial in eliminating this noise. 

•

  Turn on the instrument by flipping the switch on the power entry module on the back 

of the instrument; the instrument is designed to remain powered up at all times. 

•

  From a cold start, allow the instrument to warm-up for 60 minutes before testing. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for COMPUTRAC MAX 4000










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands