manualshive.com logo in svg

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Share
Download
Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 33

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected] 

Page 33 of 105 

6.14.  Installing & Removing the External Filter 

An optional External Filter (AZI P/N: 800-0071) is available to keep dust and other 
particulates from entering the interior of the instrument.  If the filter is being used, it should 
be inspected regularly for debris build-up and replaced when dirty.   
 

 

 

The filter can be installed and removed without placing the instrument on its side.  
However, if the instrument is going to be placed on its side, power off the instrument and 
remove the pan support first, and lay down a soft cloth or piece of cardboard to avoid 
scratching the finish on the side of the instrument. 
 
 
If the instrument is going to be laid on its side: 

•

  Power off the instrument. 

•

  Remove the pan support. 

•

  Lay the instrument on its side on a piece of soft cloth or cardboard to protect the finish. 

•

  After removal/installation is complete, set the instrument right side up before replacing 

the pan support and powering on the instrument. 

 
To install the filter: 

•

  Slide the filter into the retaining brackets with the wire lattice pattern towards the 

instrument as shown.  Orientation is also indicated by the Air Flow arrow on the side 
of the filter; the arrow points towards the instrument when the filter is installed. 

 
To remove the filter: 

•

  Push the filter from one side and pull from the other side to remove it. 

•

  If the filter is dirty, discard it and install a clean filter (AZI P/N: 800-0071). 

 
 
 
 
 
 

Summary of Contents for COMPUTRAC MAX 4000










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands