manualshive.com logo in svg

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Share
Download
Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 70

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected] 

Page 70 of 105 

8.4.1  Printer Setup 

To get here, navigate: 

[MENU]

SETUP MENU

PRINTER 

SETUP 
 
PRINTER SETUP allows the 
configuration of data output to a 
computer, printer or USB drive.  Graphics 
are not sent to the computer or USB 
drive, only to the printer.   
 
The following options are available: 

 

•

  OUTPUT TO COMPUTER enables reporting to both the RS232 and the USB 

computer ports.  Reports sent to a PC include a footer with the date and time.   

NOTE:

  This must be set to 

No

 prior to Temperature Calibration. 

•

  OUTPUT TO USB DRIVE enables reporting to a USB drive.  Make sure to insert the 

drive in the USB Type A / Host port (marked 

USB

) before printing the report.  When 

the desired report is printed, a file name is constructed from the instrument’s serial 
number with a “.TXT” extension (for example “4000005.TXT”) and saved to the drive. 
As reports are printed, they are appended to this file along with a footer listing the date 
and time.  Always wait 5 seconds after a report finishes prior to removing the drive to 
allow the instrument to close the file.  Otherwise, drive corruption can occur. 

•

  OUTPUT TO PRINTER enables reporting to the printer. 

 

•

  If using the standard printer (Y990-0212), the 

[TEST]

 soft key can be used to send a 

test pattern to the printer.  If the test pattern prints, then the printer and the MAX

®

 4000 

are communicating properly.  The 

[TEST]

 soft key does not send the test pattern to a 

connected computer, USB drive or a mini-printer. 

 
See section 

6.7 Connecting a USB Printer

 on page 

21

 and section 

6.9 Connecting a 

Computer

 on page 

22

 to connect the MAX

®

 4000 to a printer and/or a computer. 

 

8.4.2  Report Setup 

To get here, navigate: 

[MENU]

SETUP MENU

REPORT 

SETUP 
 
This menu allows the reports to be 
enabled and customized to your needs. 
 
 
 
 
 
 
 

Summary of Contents for COMPUTRAC MAX 4000










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands