manualshive.com logo in svg

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Share
Download
Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 68

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected] 

Page 68 of 105 

8.3.2.E 

Perform Verification  

Available on the MAX

®

 4000XL only 

 
To get here, navigate: 

[MENU]

CALIBRATION MENU

TEMPERATURE CALIBRATION MENU

 

PERFORM VERIFICATION 
 

This selection performs the temperature 
verification of the MAX

®

 4000 when the 

Temperature Calibration Kit is connected.  
 
Performing the verification: 

•

  Connect the Temperature Calibration 

Kit as described in section 

8.3.2 

Temperature Calibration

 on page 

63

. 

•

  Select the PERFORM 

VERIFICATION menu item. 

•

  The introduction screen is displayed; 

Follow the instructions. 

•

  Then press 

[GO]

 to continue. 

 

•

  During the verification, press 

[DETAIL]

 to view real-time results at 

each verification point, if desired. 

•

  Wait for the verification to finish. 

•

  Open the lid and wait for the MAX

®

 

4000XL to cool. 

•

  Disconnect the TCI, and remove the 

temperature calibration disk. 

•

  Gently but firmly install the pan 

support into the balance stem. 

 

 

 
During the verification, the Temperature Calibration Interface (TCI) Module reports its 
temperature to the MAX

®

 4000XL.  The verification process monitors the MAX

®

 4000XL’s 

temperature (in the heat chamber) and the TCI’s temperature, and reports the difference 
between the two. 
 
The verification can be run at any time, and can also be set to run automatically after a 
temperature calibration, as set in section 

8.3.2.B

 

Verification Setup

 on page 

66

. 

 
 
 
 
 
 

Summary of Contents for COMPUTRAC MAX 4000










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands