Arizona Instrument COMPUTRAC MAX 4000 User Manual Download Page 23

Page: 23 / 105

AZI Sales/Customer Service 800-528-7411 or 602-470-1414 or [email protected]

Page 23 of 105

6.9.1 USB Driver Setup

Before using the computer to receive information from the MAX

4000 through the USB

port, the USB driver must be installed on the PC. The USB driver is on the CD with this
manual and on the Drivers page of the AZI website at

http://www.azic.com

. The driver

works with Windows

XP (32-bit) through Windows

10.

If the CD is available:

•

Insert the CD in the PC’s CD-ROM drive.

•

Use Windows

to browse to the CD, locate the driver file (AZI_USB_Driver.zip), and

copy it to your desktop.

If the CD is not available:

•

Download the driver file from the Drivers page at

http://www.azic.com

and save it to

your desktop. If you received these instructions and the driver in an email, save the
attached file (AZI_USB_Driver.zip) to your desktop.

Once the driver file (AZI_USB_Driver.zip) is on your desktop:

•

Double-click the file to open it.

•

Drag the “Driver Install” directory from the zip file to the desktop.

•

Double-click the "Driver Install" folder to open it.

•

Double-click the "Install Driver" shortcut. This will launch the AZI Driver Installer

wizard.

Follow the instructions in the AZI Driver Installer wizard.

•

Click Next.

Summary of Contents for COMPUTRAC MAX 4000










































































































Search results

Summary of Contents for COMPUTRAC MAX 4000

Reviews:

Brands by name

Popular brands

Arizona Instrument COMPUTRAC MAX 4000, User Manual

Search results

Summary of Contents for COMPUTRAC MAX 4000

Reviews:

Brands by name

Popular brands