manualshive.com logo in svg

Arcteq AQ-G215, Instruction Manual

The Arcteq AQ-G215 Instruction Manual is available for free download from our website. This comprehensive manual provides detailed information on the installation, operation, and maintenance of the Arcteq AQ-G215, ensuring users have the necessary guidance to maximize the product's potential.

Share
Download
background image

Connections

Figure. 4.6 - 38. View of the Connections submenu.

The

Connections submenu offers the following bits of information and settings:

ETHERNET

ETHERNET

This section defines the IP settings for the ethernet port in the back panel of the unit.

• IP address: the IP address of the device which can be set by the user (the default IP address

depends on the device).

• Network: the network subnet mask is entered here.
• Gateway: the gateway is configured only when communicating with the devices in a separate

subnet.

• MAC-Address: Unique MAC address of the device. Not configurable by user.

SERIAL COM

SERIAL COM

This section defines the basic settings of RS-485 port in the back panel of the unit.

• Bitrate: displays the bitrate of the RS-485 serial communication interface (9600 bps as

standard, although can be changed to 19 200 bps or 38 400 bps if an external device

supports the faster speed).

• Databits, Parity and Stopbits: these can be set according the connected external devices.
• Protocol: by default the device does not have any serial protocol activated, although IEC

103, Modbus I/O and Modbus/RTU can be used for communication.

NO

NOTE!

TE!

When communicating with a device through a front Ethernet port connection, the IP address

is always 192.168.66.9.

SERIAL COM1 & COM2

SERIAL COM1 & COM2

SERIAL COM1 and SERIAL COM2 are reserved for serial communication option cards. They have the

same settings as RS-485 port.

A

AQ

Q-G215

-G215

Instruction manual

Version: 2.04

39

Summary of Contents for AQ-G215











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AQ-G215

Connex Protec 28 Manual preview
Protec 28
Brand: Connex Pages: 3
Mitsubishi WS-48511 Guide Service Manual preview
WS-48511 Guide
Brand: Mitsubishi Pages: 14
Belkin AP41000uk3M User Manual preview
AP41000uk3M
Brand: Belkin Pages: 30
I-Gard IPC DSP OHMNI Instruction Manual preview
IPC DSP OHMNI
Brand: I-Gard Pages: 40
NEC N8146-94 User Manual preview
N8146-94
Brand: NEC Pages: 34
NEC N8146-40 User Manual preview
N8146-40
Brand: NEC Pages: 32
Asco 4820 User Manual preview
4820
Brand: Asco Pages: 51
Schörghofer & Frehe Plisse Manual preview
Plisse
Brand: Schörghofer & Frehe Pages: 20
Arcteq AQ 102 Instruction Manual preview
AQ 102
Brand: Arcteq Pages: 46
Superfire EP7 Sonic Defenders Ultra Manual preview
EP7 Sonic Defenders Ultra
Brand: Superfire Pages: 2
LG RU-44SZ80L - - 44" Rear Projection TV Service Manual preview
RU-44SZ80L - - 44" Rear Projection TV
Brand: LG Pages: 43
Cutler-Hammer GMCP Installation Instructions preview
GMCP
Brand: Cutler-Hammer Pages: 4
Toshiba TheaterWide 56HM195 Specifications preview
TheaterWide 56HM195
Brand: Toshiba Pages: 2
Sygonix SY-3779070 Operating Instructions preview
SY-3779070
Brand: Sygonix Pages: 4
RCT Muirhead 9200 Product Manual preview
Muirhead 9200
Brand: RCT Pages: 26
INFOSEC Z3 ZenBox EX 1000 User Manual preview
Z3 ZenBox EX 1000
Brand: INFOSEC Pages: 35
Walter WaluCover Initial Installation Instructions Manual preview
WaluCover Initial
Brand: Walter Pages: 20

Brands by name

Popular brands

Load more brands