Arcteq AQ-G215 Instruction Manual Download

Page: 30 / 458

The "Registers"section stores the function's specific fault data. There are twelve (12) registers, and

each of them includes data such as opening and closing times, command types and request failures.

The data included in the register depend on the protection function. You can clear the the operation

→

"Clear".

Please note that the content of the

Registers section is not available in the HMI. It can only be

accessed via the AQtivate setting tool.

Figure. 4.5 - 23. Events section.

You can mask on and mask off events related to an object's stage in "Event mask". By default all events

are masked off. You can activate the desired events by masking them ("x"). Please remember to save

your maskings by confirming the changes with the check mark icon. If you want to cancel the changes,

select the strike-through circle to do so. Only masked events are recorded to the event history (which

can be accessed in the "Events" view in the user view section).

Control functions

Once a control function has been activated in the

Controls

→

Controls enabled submenu, its own

submenu can be opened. In the image series below, the user has activated three control functions. The

user accesses the list of activated control stages through the "Control functions" module, and selects

the control function for further inspection.

Figure. 4.5 - 24. Control functions submenu.

Q-G215

-G215

Instruction manual

Version: 2.04

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands