Arcteq AQ-G215 Instruction Manual Download

Page: 221 / 458

Figure. 5.3.17 - 153. Comparing dual time constant thermal replica tripping curves to given motor thermal characteristics.

As the figures above have shown, with estimated time constants from the motor thermal limit

curves the single time constant model underprotects the motor in the stall condition when the motor is

cold. When the motor is hot the model overprotects with a heavy hand, allowing the motor only 30.5

seconds of stalling time of the approximately 67 seconds the motor can withstand. When dual time

constants and dynamic time constants are in use, the relay automatically selects the correct tripping

curves for the thermal replica according to the settings, producing therefore an exact thermal image

response (as compared to the single time constant thermal image). In overload conditions the

response from both of the thermal replicas is acceptable as even a small overshoot is noticed when the

motor is hot. In the curve simulations the hot condition was defined as 70 % of the thermal capacity.

The following figures present the tripping and cooling curves of the thermal replica.

Q-G215

-G215

Instruction manual

Version: 2.04

220

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands