Arcteq AQ-G215 Instruction Manual Download

Page: 121 / 458

Unearthed network

Figure. 5.3.5 - 93. Angle tracking of I0dir> function (unearthed network model) (32N)

When the unearthed (capacitive) network mode is chosen, the device expects the fault current to be

lagging zero sequence voltage by 90 degrees. Healthy phases of healthy feeders produce capacitive

current during earth fault just like a faulty feeder but the current is floating towards the busbar and

through an incoming transformer or a earthing transformer and into a faulty feeder. Healthy feeders do

not trip since capacitive current is floating to the opposite direction and selective tripping can be

ensured.

The amplitude of the fault current depends on the capacitance of the network. The outgoing feeders

are the sources for capacitive currents. The bigger the network the greater the capacitive current

during a fault. Each outgoing feeder produces capacitance according to the zero sequence capacitive

reactance of the line (ohms per kilometer). It is normal that in cable networks fault currents are higher

than in overhead lines.

Q-G215

-G215

Instruction manual

Version: 2.04

120

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands