Arcteq AQ-G215 Instruction Manual Download | Manualshive

Page: 381 / 458

background image

Name

Range

Step Default

Description

Power measurement update

interval

500…10

000ms

5ms

2

000ms

Defines the measurement update interval of all power-related

measurements.

Impedance

measurement update interval

500…10

000ms

5ms

2

000ms

Defines the measurement update interval of all impedance-

related measurements.

6.1.3 Modbus I/O

The Modbus I/O protocol can be selected to communicate on the available serial ports. The Modbus I/

O is actually a Modbus/RTU master implementation that is dedicated to communicating with serial

Modbus/RTU slaves such as RTD input modules. Up to three (3) Modbus/RTU slaves can be

connected to the same bus polled by the Modbus I/O implementation. These are named I/O Module A,

I/O Module B and I/O Module C. Each of the modules can be configured using parameters in the

following two tables.

Table. 6.1.3 - 269. Module settings.

Name

Range

Description

I/O module X

address

0…247

Defines the Modbus unit address for the selected I/O Module (A, B, or C). If this setting

is set to "0", the selected module is not in use.

Module x

type

0: ADAM-4018+

1: ADAM-4015

Selects the module type.

Channels in

use

Channel

0…Channel 7 (or

None)

Selects the number of channels to be used by the module.

Table. 6.1.3 - 270. Channel settings.

Name

Range

Step Default

Description

T.C.

type

0: +/- 20mA

1: 4…20mA

2: Type J

3: Type K

4: Type T

5: Type E

6: Type R

7: Type S

-

1:

4…20mA

Selects the thermocouple or the mA input connected to the I/O module.

Types J, K, T and E are nickel-alloy thermocouples, while Types R and S are

platinum/rhodium-alloy thermocouples.

Input

value

-101.0…2

000.0

0.1

-

Displays the input value of the selected channel.

Input

status

0: Invalid

1: OK

-

-

Displays the input status of the selected channel.

6.1.4 IEC 61850

The user can enable the IEC 61850 protocol in device models that support this protocol at

Communication

→

Protocols

→

IEC61850. AQ-21x frame units support Edition 1 of IEC 61850.

AQ-25x frame units support both Edition 1 and 2 of IEC61850. The following services are supported by

IEC 61850 in Arcteq devices:

• Up to six data sets (predefined data sets can be edited with the IEC 61850 tool in AQtivate)
• Report Control Blocks (both buffered and unbuffered reporting)
• Control ('Direct operate with normal security’, ’Select before operate with normal

security, ’Direct with enhanced security’ and ’Select before operate with enhanced

sequrity’ control sequences)

• Disturbance recording file transfer
• GOOSE

A

AQ

Q-G215

-G215

Instruction manual

Version: 2.04

380

«
...
379
380
381
382
383
...
»

Summary of Contents for AQ-G215











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AQ-G215

DynaShield ADS 2F Series

Brand: ALLTEC Pages: 12

CPS 5900 Training

Brand: Dräger Pages: 24

Brand: SPM Pages: 30

Brand: Philips Pages: 54

Brand: Philips Pages: 60

55 IN DIGITAL WIDESCREEN HDTV MONITOR 55PW9363

Brand: Philips Pages: 2

55I WIDESCREEN PROJECTION HDTV MONITOR 55PP9701

Brand: Philips Pages: 2

55-HDTV MONITOR PROJECTION TV PIXEL PLUS 55PP9753 -

Brand: Philips Pages: 80

Brand: Philips Pages: 60

Brand: Philips Pages: 56

Brand: Philips Pages: 2

55I WIDESCREEN PROJECTION HDTV MONITOR 55PP9701

Brand: Philips Pages: 60

Brand: ABB Pages: 150

Relion 670 series

Brand: ABB Pages: 50

Brand: Sony Pages: 28

Brand: Sony Pages: 42

Brand: Sony Pages: 59

Airkos CR-2B01/2013

Brand: Weltek Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands