Arcteq AQ-G215 Instruction Manual Download

Page: 17 / 458

Name

Range

Step

Default

Description

Language

0: User defined

1: English

2: Finnish

3: Swedish

4: Spanish

5: French

6: German

7: Russian

8: Ukraine

1: English

Changes the language of the parameter descriptions in

the HMI. If the language has been set to "Other" in the

settings of the AQtivate setting tool, AQtivate follows the

value set into this parameter.

UTC time

Displays the UTC time used by the unit without time

zone corrections.

Clear events

0: -

1: Clear

0: -

Clears the event history recorded in the AQ-200 device.

LCD Contrast

0…255

120

Changes the contrast of the LCD display.

Return to default view

0…3600 s

10 s

0 s

If the user navigates to a menu and gives no input after

a period of time defined with this parameter, the unit

automatically returns to the default view. If set to 0 s, this

feature is not in use.

LED test

0: -

1: Activated

0: -

When activated, all LEDs are lit up. LEDs with multiple

possible colors blink each color.

Reset latches

0: -

1: Reset

0: -

Resets the latched signals in the logic and the matrix.

When a reset command is given, the parameter

automatically returns back to "-".

Measurement recorder 0: Disabled

1: Enabled

0: Disabled

Enables the measurement recorder tool, further

configured in

Tools

→

Misc

→

Measurement recorder.

Reconfigure mimic

0: -

1: Reconfigure

0: -

Reloads the mimic to the unit.

Reset last fault

registers

Activation of input selected here resets the values in

"Fault registers" view in carousel.

Protection/Control/

Monitor profile

Displays the status of all enabled functions.

Function comments

Function comments displays notes of each function that has been activated in the Protection, Control

and Monitoring menu. Function notes can be edited by the user.

Q-G215

-G215

Instruction manual

Version: 2.04

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands