Arcteq AQ-G215 Instruction Manual Download

Page: 46 / 458

Voltage measurement

Figure. 4.7 - 46. Voltage measurement submenu and System Voltages menu.

Voltage measurement submenu includes various individual measurements for each phase or phase-to-

phase measurement.

The

Voltage measurement submenu has been also divided into four sections: "Voltage inputs",

"Sequence voltages", "System voltages", and "Harmonics".

• "Voltage inputs" displays the values of per-unit and secondary voltages as well as phase

angles.

• "Sequence voltages" displays the per-unit, primary and secondary voltages as well as phase

angles, and it calculates the positive, negative and neutral sequence voltages.

• "System voltages" displays primary voltage magnitudes and primary voltage angles.
• "Harmonics" displays harmonics up to the 31

harmonic for all four voltages (U1, U2, U3,

U4); each component can be displayed as absolute or percentage values, and as primary or

secondary voltages or in per-unit values.

Q-G215

-G215

Instruction manual

Version: 2.04

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands