Arcteq AQ-G215 Instruction Manual Download

Page: 126 / 458

The new broad range mode is capable of detecting an earth fault directionally in both unearthed and

compensated networks not only by combining the two stages together but by using a new multi-criteria

detection. This optional additional tripping condition for compensated networks uses Arcteq’s patented,

high-resolution intermittent earth fault algorithm with added symmetrical component calculation of

phase currents and voltages. If this mode is activated, the alarming criteria is comprised of a measured

residual current in the fourth quadrant and the symmetrical components of voltages and currents

detecting a fault. No extra parameterization is required compared to the traditional method. The multi-

criteria algorithm can be tested with COMTRADE files supplied by Arcteq. The function requires a

connection of three-phase currents, residual current and residual voltage to operate correctly.

To avoid unnecessary alarms the user can add an encroachment area against I0 CT errors in

compensated long healthy lines.

Figure. 5.3.5 - 97. Effect of angle divider when in use and when disabled.

To receive a more accurate indication as to whether the fault was in a compensated or an unearthed

network the angle divider can divide the area which would otherwise be overlapped between the two

network models. By default the setting is 45 degrees. When the divider is disabled the angle is set to

zero degrees.

Read-only parameters

The relay's

Info page displays useful, real-time information on the state of the protection function. It is

accessed either through the relay's HMI display, or through the setting tool software when it is

connected to the relay and its Live Edit mode is active.

Table. 5.3.5 - 72. Information displayed by the function.

Name

Range

Step

Description

I0dir>

condition

0: Normal

1: Start

2: Trip

3: Blocked

Displays the status of the protection function.

U0>

Measuring

now

0: No U0 avail!

1: U0Calc

2: U3 Input

3: U4 Input

Displays which voltage channel is used by the function. If no voltage

channel has been selected the function defaults to calculated

residual voltage if line-to-neutral voltages have been connected to

device. If no channel is set to "U0" mode and line-to-line voltages are

connected, no residual voltage is available and "No U0 avail!" will be

displayed.

Q-G215

-G215

Instruction manual

Version: 2.04

125

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands