Arcteq AQ-G215 Instruction Manual Download

Page: 339 / 458

Signal

Description

Time base

I02RMS

RMS measurement of residual input I02

5ms

Phase current's positive sequence component

5ms

Phase current's negative sequence component

5ms

IL1Ang

Angle of phase L1 (A) current

5ms

IL2 Ang

Angle of phase L2 (B) current

5ms

IL3 Ang

Angle of phase L3 (C) current

5ms

I01 Ang

Angle of residual input I01

5ms

I02 Ang

Angle of residual input I02

5ms

The selection of the AI channel in use is made with a setting parameter. In all possible input channel

variations the pre-fault condition is presented with a 20 ms averaged history value from -20 ms from

START or TRIP event.

Table. 5.5.1 - 231. Residual current input signal settings

Name

Range Step Default

Description

I0 input selection

0: Not in

use

1: I01

2: I02

0: Not

in use

Selects the measurement input for the residual current. If the residual

current is measured with a separate CT, the residual current circuit can be

monitored with the CTS function as well. However, this does not apply to

summing connections (Holmgren, etc.). If the phase current CT is summed

with I01 or I02, this selection should be set to "Not in use".

I0 direction

0: Add

Subtract

0: Add

Defines the polarity of residual current channel connection.

Comp.

natural unbalance

0: -

Comp

0: -

When activated while the line is energized, the currently present calculated

residual current is compensated to 0.

Pick-up

The

set

and

set

setting parameters control the current-dependent pick-up and activation of the

current transformer supervision function. They define the minimum and maximum allowed measured

current before action from the function. The function constantly calculates the ratio between the setting

values and the measured magnitude (

) for each of the three phases and for the selected residual

current input. The reset ratio of 97 % and 103% are built into the function and is always relative to the

set

value. The setting value is common for all measured amplitudes, and when the

exceeds the

set

value (in single, dual or all currents) it triggers the pick-up operation of the function.

Table. 5.5.1 - 232. Pick-up settings.

Name

Range

Step

Default

Description

set

high

limit

0.01…40.00×I

0.01×I

1.20×I

Determines the pick-up threshold for phase current measurement. This

setting limit defines the upper limit for the phase current's pick-up

element.

If this condition is met, it is considered as fault and the function is not

activated.

set

low

limit

0.01…40.00×I

0.01×I

0.10×I

Determines the pick-up threshold for phase current measurement. This

setting limit defines the lower limit for the phase current's pick-up

element.

This condition has to be met for the function to activate.

Q-G215

-G215

Instruction manual

Version: 2.04

338

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands