Arcteq AQ-G215 Instruction Manual Download

Page: 442 / 458

Thermal replica temperature estimates

Selectable between °C and °F

Ambient temperature effect

k min. and max. range

Ambient temperature min. and max. range

Linear or manually set curve

0.01...5.00 × I

, setting step 0.01 × I

–60…500 deg, setting step 1 deg

Thermal model biasing (ambient):

- Set ambient temperature

- RTD

–60…500 deg, setting step 1 deg

Used measured ambient value

9.2.1.14 Power protection (P, Q, S>/<; 32)

Table. 9.2.1.14 - 322. Technical data for the power protection function.

Measurement inputs

Current inputs

Phase current inputs: I

(A), I

(B), I

(C)

Voltage inputs

, U

L12

, U

L23

, U

L31

(+ U

)

Calculated measurements

Three-phase active, reactive or apparent power (P, Q or S) value based on the chosen or

set nominal amplitude.

Pick-up

Comparator selection

> or <

-500.000...500.000 %/MVA

, setting step 0.005 %/MVA

Inaccuracy:

- Active, reactive, or apparent

power

Typically <1.0 %P

SET

Operation time

Definite time function operating

time setting

0.00…1800.00 s, setting step 0.005 s

Inaccuracy:

- Definite time (P

SET

ratio

1.05

→

)

±1.0 % or ±35 ms

Instant operation time

Start time and instant operation

time (trip):

- PQS

/PQS

SET

ratio 1.05

→

<40 ms

Reset

Reset ratio

97 or 103 %P

SET

Instant reset time and start-up

reset

<40 ms

Notte!

• The voltage measurement starts from 0.5 V and the current measurement from 25 mA. In

case either or both are missing, the measured magnitude is forced to 0 MW/MVar/MVA.

Please avoid using settings that should operate below the relay's current squelch limit (25 mA

on the relay terminal).

• With very small under power pick-up settings time delay inaccuracy might double.

9.2.1.15 Underimpedance protection (Z<; 21U)

Table. 9.2.1.15 - 323. Technical data for the underimpedance function.

Measurement inputs

Q-G215

-G215

Instruction manual

Version: 2.04

441

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands