Arcteq AQ-G215 Instruction Manual Download

Page: 44 / 458

VT primary and secondary voltages must match with the connected voltage transformer in addition to

the voltage measurement mode. These settings are then used for scaling the voltage channel input

voltages to primary and per unit values as well as power and energy measurement values if current

measurements are also available.

Frequency

Figure. 4.7 - 44. Frequency submenu.

Frequency measurements use the fixed sampling mode as the default, and "System nominal

frequency" should be set to the desired level. When "Sampling mode" is set to "Tracking", the device

uses the measured frequency value as the system nominal frequency. There are three frequency

reference channels: f Ref1, fRef2 and fRef3. With these parameters it is possible to set up three voltage

or current channels to be used for frequency sampling. Parameter "f.meas in use" indicates which of

the three channels are used for sampling if any.

Q-G215

-G215

Instruction manual

Version: 2.04

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands