Arcteq AQ-G215 Instruction Manual Download

Page: 161 / 458

Name

Range

Step

Description

Expected

operating

time

0.000...1800.000s

0.005s

Displays the expected operating time when a fault occurs. When IDMT

mode is used, the expected operating time depends on the measured

voltage value. If the measured voltage changes during a fault, the

expected operating time changes accordingly.

Time

remaining

to trip

-1800.000...1800.000s 0.005s

When the function has detected a fault and counts down time towards a

trip, this displays how much time is left before tripping occurs.

A(B)

meas

set

at the

moment

0.00...1250.00U

set

0.01U

set

The ratio between U

or U

voltage and the pick-up value.

B(c)

meas

set

at the

moment

0.00...1250.00U

set

0.01U

set

The ratio between U

or U

voltage and the pick-up value.

C(A)

meas

set

at the

moment

0.00...1250.00U

set

0.01U

set

The ratio between U

or U

voltage and the pick-up value.

meas

set

at the

moment

0.00...1250.00U

set

0.01U

set

The ratio between the measured voltage and the pick-up value.

Function blocking

The block signal is checked in the beginning of each program cycle. The blocking signal is received

from the blocking matrix in the function's dedicated input. If the blocking signal is not activated when

the pick-up element activates, a START signal is generated and the function proceeds to the time

characteristics calculation.

If the blocking signal is active when the pick-up element activates, a BLOCKED signal is generated and

the function does not process the situation further. If the START function has been activated before the

blocking signal, it resets and the release time characteristics are processed similarly to when the pick-

up signal is reset.

The blocking of the function causes an HMI display event and a time-stamped blocking event with

information of the startup voltage values and its fault type to be issued.

The blocking signal can also be tested in the commissioning phase by a software switch signal when

the relay's testing mode "Enable stage forcing" is activated (

General

→

Device).

The variables the user can set are binary signals from the system. The blocking signal needs to reach

the device minimum of 5 ms before the set operating delay has passed in order for the blocking to

activate in time.

Operating time characteristics for trip and reset

The operating timers’ behavior during a function can be set for TRIP signal and also for the release of

the function in case the pick-up element is reset before the trip time has been reached. There are three

basic operating modes available for the function:

• Instant operation: gives the TRIP signal with no additional time delay simultaneously with the

START signal.

• Definite time operation (DT): gives the TRIP signal after a user-defined time delay regardless

of the measured voltage as long as the voltage is above the

set

value and thus the pick-up

element is active (independent time characteristics).

Q-G215

-G215

Instruction manual

Version: 2.04

160

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands