Arcteq AQ-G215 Instruction Manual Download

Page: 144 / 458

Signal

Description

Time base

IL3RMS

RMS measurement of phase L3 (C) current

5ms

I01RMS

RMS measurement of residual input I01

5ms

I02RMS

RMS measurement of residual input I02

5ms

I0Calc

Calculated residual current from the phase current inputs

5ms

DOIN

Monitors digital output relay status

5ms

DIIN

Monitors digital input status

5ms

The selection of the used AI channel is made with a setting parameter. In all possible input channel

variations the pre-fault condition is presented with a 20 ms averaged history value from -20 ms

from START or TRIP event.

General settings

The following general settings define the general behavior of the function. These settings are static i.e.

it is not possible to change them by editing the setting group.

Table. 5.3.8 - 88. CBFP monitoring signal definitions.

Name

Description

Signal

monitor

Defines which TRIP events of the used protection functions trigger the CBFP countdown. For the CBFP function to

monitor the signals selected here, the "Operation mode selection" parameter must be set to a mode that includes

signals (e.g. "Signals only", "Signals or DO", "Current and signals and DO").

Trip

monitor

Defines which output relay of the used protection functions trigger the CBFP countdown. For the CBFP function to

monitor the output relays selected here, the "Operation mode selection" parameter must be set to a mode that

includes digital outputs (e.g. "DO only", "Current and DO", "Current or signals or DO").

Pick-up

The setting parameters

set

and

set

control the pick-up and the activation of the current-dependent

CBFP function. They define the minimum allowed measured current before action from the function.

The function constantly calculates the ratio between the

set

or the

set

and the measured magnitude

(

) for each of the three phases and the selected residual current input. The reset ratio of 97 % is built

into the function and is always relative to the

set

value. The setting value is common for all measured

phases. When the

exceeds the

set

value (in single, dual or all phases) it triggers the pick-up

operation of the function.

Table. 5.3.8 - 89. Operating mode and input signals selection.

Name

Range

Step Default

Description

I0Input

0: Not in use

1: I01

2: I02

3: I0Calc

0: Not

in use

Selects the residual current monitoring source, which can be either from the two

separate residual measurements (I01 and I02) or from the phase current's

calculated residual current.

Q-G215

-G215

Instruction manual

Version: 2.04

143

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands