manualshive.com logo in svg

Arcteq AQ-G215, Instruction Manual

The Arcteq AQ-G215 Instruction Manual is available for free download from our website. This comprehensive manual provides detailed information on the installation, operation, and maintenance of the Arcteq AQ-G215, ensuring users have the necessary guidance to maximize the product's potential.

Share
Download
background image

•

Ch

an

= the number of analog channels recorded; "+ 1" stands for the time stamp for each

recorded sample.

•

SR = the selected sample rate (s/c).

• 200 Hz = the rate at which digital channels are always recorded, i.e. 5 ms.
•

Ch

dig

= the number of digital channels recorded.

For example, let us say the nominal frequency is 50 Hz, the selected sample rate is 64 s/c, nine (9)

analog channels and two (2) digital channels record. The calculation is as follows:

Therefore, the maximum recording length in our example is approximately 496 seconds.

Application example

This chapter presents an application example of how to set the disturbance recorder and analyze its

output. The recorder is configured by using the setting tool software or relay HMI, and the results are

analyzed with the AQviewer software (is automatically downloaded and installed with

AQtivate). Registered users can download the latest tools from the Arcteq website

(

arcteq.fi./downloads/

).

In this example, we want the recordings to be made according to the following specifications:

• the recording length is 6.0 s
• the sample rate is 64 s/c (therefore, with a 50 Hz system frequency a sample is taken every

312.5 µs)

• the analog channels 1...8 are used
• digital channels are tracked every 5 ms
• the first activation of the overcurrent stage trip (I> TRIP) triggers the recorder
• the pre-triggering time is 5 (ie. how long is recorded before the I> TRIP signal) and the post-

triggering time is 1 s

The image below shows how these settings are placed in the setting tool.

A

AQ

Q-G215

-G215

Instruction manual

Version: 2.04

365

Summary of Contents for AQ-G215











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AQ-G215

Akai PT61DL34 Specifications preview
PT61DL34
Brand: Akai Pages: 2
Lyon LPP0027 User Instructions preview
LPP0027
Brand: Lyon Pages: 12
Chamberlain CPS-RPEN4 Manual preview
CPS-RPEN4
Brand: Chamberlain Pages: 16
Westland Bimini Top Installation Instructions preview
Bimini Top
Brand: Westland Pages: 2
Trend Micro TPS 2200T Hardware Specification And Installation Manual preview
TPS 2200T
Brand: Trend Micro Pages: 34
SENTRY GUARDING SYSTEM 600 GUARDING Installation Manual preview
600 GUARDING
Brand: SENTRY GUARDING SYSTEM Pages: 2
Micom P721 Technical Manual preview
P721
Brand: Micom Pages: 334
Micom P631 Technical Manual preview
P631
Brand: Micom Pages: 638

Brands by name

Popular brands

Load more brands