background image

SSB- 6113 
120Amp, 12V/24V Programmable Battery Protector 

 

 
 
 
 
 
 
 
 

Operation Manual 

 

Keep this manual in a safe place for quick reference at all times. 

 

This manual contains important safety and operation instructions for correct use of the battery protector. 

Read through the manual and pay special attention to the markings and labels of the protector, 

battery and equipment connected to the battery system. 

 

Pay special attention to these two types of notices used in this manual. 

 

WARNING: 

Failure to heed this warning may cause injury to persons and damage to Equipment. 

 

CAUTION: 

Failure to observe this warning may result in damage to equipment 

and improper functioning of the protector. 

 

Warning and Precautions 
 

 

The protector is not designed for any life saving application. 

● 

The protector is not designed for environments that would allow water to come in contact with terminals on the housing 

 

which would result a short circuit. 

● 

Install the protector in environments with sufficient ventilated space around the unit to allow dissipation of heat at the 

 

surface, a minimum of 50mm surrounding space is required. 

● 

Wear protective goggles and turn your face away when connecting or disconnecting the battery. 

● 

Never smoke, use an open flame, or create sparks near battery or protector during normal operation as batteries may give 

 

out explosive gas. 

● 

Do not use the protector if it has been dropped or damaged. 

● 

Do not remove casing of the protector, there is no user -serviceable parts inside. 

● 

If the protector does not work properly or if it has been damaged, unplug all DC connections. 

 
Copy Right 
 
All rights reserved. 
No part of this publication may be reproduced, or transmitted in any form or by any means without the written 
permission from Manson Engineering Industrial Ltd. 
 
Changes in the manual. 
Manson Engineering Industrial Ltd. has the right to update and change the content of this manual without any prior 
notice and obligation. 
 
Disclaimer 
 
Exclusions for documentation, Indemnity and Product application. 
Manson Engineering Industrial Ltd. (Manson) 
1) 

Assumes no warranty to the accuracy, suitability of technical information given in the user manuals or other documentation. 

2) 

Undertakes no responsibility or liability of losses, damages and related expenses whether specific, direct, indirect 

 

consequential or accidental which might result from the use of information given in this manual. 

3) 

Shall not be liable to anyone for any special, collateral, incidental or consequential damages in connection with or from the 

 

use of these Manson products. The sole and exclusive liability to Manson, regardless of the form of action shall not exceed 

 

the purchase price of the Manson product. 

 

Summary of Contents for SSB-6113









Reviews: