Anite NEMO FSR1 Manual Download

Page: 103 / 137

PC T EL

1 0 3

If the requested frequency range is not supported by the device, Nemo Outdoor automatically

adjusts the frequency range for the device, and only frequency ranges supported by the

scanning receiver are used to make spectrum analyzer measurements. The number of samples

is used only for the frequency range supported by the scanning receiver. Nemo Outdoor does

not read the supported frequency range from the scanning receiver. For example, in the picture

below the user has set start and stop frequencies as seen within the red area. However, the

scanning receiver supports only frequency ranges shown by the green areas. The number of

samples is used only for green areas and the correct RBW is selected accordingly.

7. Click

to return to the Spectrum scanning page.

Summary of Contents for NEMO FSR1










































































































































Search results

Summary of Contents for NEMO FSR1

Reviews:

Related manuals for NEMO FSR1

Brands by name

Popular brands

Anite NEMO FSR1, Manual

Search results

Summary of Contents for NEMO FSR1

Reviews:

Related manuals for NEMO FSR1

Brands by name

Popular brands