Amazone Cirrus 3002 Operating Manual Download Page 96

Page: 96 / 209

Commissioning

6.1.1.1

Data required for the calculation (hitched machine)

Fig. 100

[kg] Tractor empty weight

See tractor operating manual or vehicle

documentation

[kg] Front axle load of the unladen tractor

[kg] Rear axle load of the unladen tractor

[kg] Front weight (if available)

See front weight in technical data, or weigh

[kg] Maximum drawbar load

See section "Technical data“, Seite 55

a [m] Distance between the centre of gravity of

the front machine mounting or the front

weight and the centre of the front axle (total

+ a

)

See technical data of tractor and front ma-

chine mounting or front weight or measure-

ment

[m] Distance from the centre of the front axle to

the centre of the lower link connection

See tractor operating manual or measure-

ment

[m] Distance between the centre of the lower

link connection point and the centre of grav-

ity of the front-mounted machine or front

ballast (centre of gravity distance)

See technical data of front machine mount-

ing or front weight or measurement

b [m] Tractor wheel base

See tractor operating manual or vehicle

documents or measurement

[m] Distance between the centre of the rear

axle and the centre of the lower link con-

nection

See tractor operating manual or vehicle

documents or measurement

Cirrus BAH0049-1 09.14

Summary of Contents for Cirrus 3002


















































































































































































































Search results

Summary of Contents for Cirrus 3002

Reviews:

Brands by name

Popular brands

Amazone Cirrus 3002, Operating Manual

Search results

Summary of Contents for Cirrus 3002

Reviews:

Brands by name

Popular brands