manualshive.com logo in svg

Amazone Cirrus 3002, Operating Manual

Share
Download
Amazone Cirrus 3002 Operating Manual Download Page 109

 

 

 

 

Coupling and uncoupling the machine 

 

7.1.2 

Connecting the electrical connections 

Connection/function 

Installation information 

Plug (7-pin) for the road traffic lighting system 

 

AMATRON 3 machine plug 

Connect the plugs to the terminal as described in 

the AMATRON 3 operating manual. 

7.1.3 

Connecting the pneumatic service brake system 

Tractor connection 

Function 

Connection 

Marking 

Brake line 

Yellow 

Pneumatic braking system 

Supply line 

Red 

 

 

Couple to the tractor 

•

 

first of all the yellow hose coupling (brake line)  

•

 

then the red hose coupling (supply line).  

Make sure that they engage correctly! 
The brake is released immediately from braked position (braked posi-

tion possible only if the compressed air tank is full) when the red hose 

coupling is coupled.  
Before coupling the brake line or supply line ensure that the 

•

 

hose couplings are clean 

•

 

the sealing rings of the hose couplings are in perfect condition 

•

 

the seals are clean and undamaged. 

Cirrus  BAH0049-1  09.14

 

109 

 

Summary of Contents for Cirrus 3002


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands