Amazone Cirrus 3002 Operating Manual Download Page 150

Page: 150 / 209

Use of the machine

When using the machine, observe the information in the sections

•

"Warning pictograms and other signs on the machine", Seite 19

and

•

"Safety information for users", Seite 31.

Observing this information is important for your safety.

WARNING

Danger of breaking during operation, insufficient stability and
insufficient tractor steering and braking power on improper use
of the tractor!

Comply with the maximum load of the connected machine and the

approved axle and support loads of the tractor. Drive only with empty

hopper.

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
through insufficient stability and tipping of the tractor and/or the
connected machine.

Drive in such a way that you always have full control over the tractor

with the attached machine.
In so doing, take your personal abilities into account, as well as the

road, traffic, visibility and weather conditions, the driving characteris-

tics of the driver and the attached machine.

WARNING

Risk of contusions, drawing in and catching during machine
operation without the intended protective equipment!

Only ever start up the machine when the protective equipment is fully

installed.

Only actuate the tractor control units from inside the tractor cab!

150

Cirrus BAH0049-1 09.14

Summary of Contents for Cirrus 3002


















































































































































































































Search results

Summary of Contents for Cirrus 3002

Reviews:

Brands by name

Popular brands

Amazone Cirrus 3002, Operating Manual

Search results

Summary of Contents for Cirrus 3002

Reviews:

Brands by name

Popular brands