Amazone Cirrus 3002 Operating Manual Download Page 141

Page: 141 / 209

Transportation

WARNING

Danger of breaking during operation, insufficient stability and
insufficient tractor steering and braking power on improper use
of the tractor!

These risks pose serious injuries or death.
Comply with the maximum load of the connected machine and the

approved axle and support loads of the tractor. Drive only with empty

hopper.

WARNING

Risk of falling from the machine if riding against regulations!

It is forbidden to ride on the machine and/or climb the running ma-

chine.
Instruct people to leave the loading site before approaching the ma-

chine.

WARNING

Risk of stabbing other road users during transportation from
uncovered, sharp spring tines of the exact harrow on the central
part of the machine pointing backwards!

Transportation without a correctly fitted transport guard rail is forbid-

den.

Moving the Cirrus to transport position on the field after work

1. Fold in both track markers (see AMATRON 3 operating manual).
2. Apply the tractor parking brake, switch off the tractor engine and

remove the ignition key.

DANGER

Apply the tractor parking brake, switch off the tractor engine and
remove the ignition key.

Cirrus BAH0049-1 09.14

141

Summary of Contents for Cirrus 3002


















































































































































































































Search results

Summary of Contents for Cirrus 3002

Reviews:

Brands by name

Popular brands

Amazone Cirrus 3002, Operating Manual

Search results

Summary of Contents for Cirrus 3002

Reviews:

Brands by name

Popular brands