Altigen IP 710 Administration Manual Download

Page: 64 / 75

LCD Messages

IP 710 Manual

IP Phone Running Messages

The following messages may be displayed in the LCD when running the
IP 710:

Message

Definition

AW UNREACHABLE!

Failed to connect to the AltiGen phone server. The user
is trying to register the IP phone with an invalid IP
phone’s IP address or the AltiGen Phone Server's IP
address is invalid.

Or, the network connection is lost in offhook or connect
state.

Refer to “

AltiWare is unreachable

” section of

“Troubleshooting” on page 49.

Basic-Idle!

IP phone is operating in Basic mode.

Press #27 again to reactivate.

Check IP Phone Service

Verify extension is configured for dynamic.

DHCP FAIL!

Although DHCP was enabled, the IP 710 was not able to
receive the IP address from the DHCP server.

DUPLICATE IP!

Another device configured with the same IP address as
the IP phone is detected. The IP phone cannot function
correctly until this is corrected.

INVALID IP!

INPUT AGAIN...

The inputted IP address is invalid.

INVALID VAL!

During register of IP extension, an invalid response
(return value) returned from phone server.

NO IP ADDR!

IP 710 cannot attach an IP address due to network
failure.

No Network!

Phone has lost Ethernet connection.

Cannot register to the AltiGen phone server.

IP extension registered successfully.

Summary of Contents for IP 710












































































Search results

Summary of Contents for IP 710

Reviews:

Related manuals for IP 710

Brands by name

Popular brands

Altigen IP 710, Administration Manual

Search results

Summary of Contents for IP 710

Reviews:

Related manuals for IP 710

Brands by name

Popular brands