Allied Telesis AT-S63 Features Manual Download Page 81 | Manualshive

Page: 81 / 538

background image

AT-S63 Management Software Features Guide

Section I: Basic Operations

81

Common VLAN

A master switch searches for the other switches in an enhanced stack by
sending out a broadcast packet out a local subnet. (The designation of this
subnet is explained in “Master Switch and the Local Interface,” next.)
Since a broadcast packet cannot cross a router or a VLAN boundary, you
must connect the switches of an enhanced stack with a common VLAN.
The VLAN acts as the transfer path for the broadcast packets from the
master switch to the slave switches and also serves as the path for other
management packets.

Here are several things to keep in mind as you plan the common VLAN of
your enhanced stack:

Any valid VLAN name and VLAN identifier (VID) can be used for the
common VLAN, but it should be the same on all the switches in the
stack.

A slave switch of an enhanced stack can be indirectly connected to the
master switch through other switches, provided there is an
uninterrupted path of the common VLAN from the slave switch to the
master switch.

The Default_VLAN can be used as the common VLAN.

The common VLAN does not have to be dedicated solely to the
enhanced stacking feature.

For background information on port-based and tagged virtual LANs, refer
to “Overview” on page 271.

«
...
79
80
81
82
83
...
»

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

Brand: Generic Media Pages: 17

RayTech RNS 5.0

Brand: Raymarine Pages: 152

Membrain Software

Brand: SanDisk Pages: 14

BJ0NJML - Service And Asset Management

Brand: IBM Pages: 330

Brand: Alcatel Pages: 4

DEEP FREEZE - INTEGRATING WITH ALTIRIS...

Brand: FARONICS Pages: 22

Brand: R&S Pages: 262

ENTERPRISE SOLUTION ERASING FI

Brand: Blackberry Pages: 10

APPLICATION STACK 2.2 RELEASE

Brand: Red Hat Pages: 22

Brand: Measurement Computing Pages: 109

Brand: LEI Extras Pages: 8

Brand: FieldServer Pages: 22

Brand: Autodesk Pages: 6

23802-091408-9020 - PSG Dwf Composer 2

Brand: Autodesk Pages: 12

Brand: Ubiquiti Pages: 38

Brand: IBM Pages: 590

FLASH MEDIA SERVER 2-SERVER MANAGEMENT ACTIONSCRIPT...

Brand: MACROMEDIA Pages: 74

Brand: TC Electronic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands