Allied Telesis AT-S63 Features Manual Download Page 123 | Manualshive

Page: 123 / 538

background image

AT-S63 Management Software Features Guide

Section II: Advanced Operations

123

Overview

A managed switch is a complex piece of computer equipment that includes
both hardware and software. Multiple software features operate
simultaneously, interoperating with each other and processing large
amounts of network traffic. It is often difficult to determine exactly what is
happening when a switch appears not to be operating normally, or what
happened when a problem occurred.

The operation of the switch can be monitored by viewing the event
messages generated by the device. These events and the vital information
about system activity that they provide can help identify and solve system
problems.

Event Messages

Event messages include the following information:

The time and date of the event

The severity of the event

The management module that generated the event

An event description

The switch has two event logs for storing the event messages. One log is
located in temporary memory and has a storage capacity of up to 4,000
entries. The events in this log are purged whenever you reset or power
cycle the switch. The second log is located in permanent memory and has
a maximum storage capacity of 2,000 entries. Events in this log are
retained when the switch is reset or power cycled. Both logs store the
same events messages. You can view either log to display the events of
the switch since the unit was last reset. But to view the events that
preceded a system reset, you must view the permanent event log.

«
...
121
122
123
124
125
...
»

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

imagePROGRAF W6400

Brand: Canon Pages: 84

Vantage Pro2 Updater

Brand: DAVIS Pages: 12

Brand: Accordiva Pages: 31

COLDFUSION STUDIO 4.5-USING COLDFUSION...

Brand: MACROMEDIA Pages: 236

3CR15800 - Intelligent Management Center Enterprise...

Brand: 3Com Pages: 4

Brand: Cpanel Pages: 221

NetAtlas Workgroup

Brand: ZyXEL Communications Pages: 242

Brand: FujiFilm Pages: 55

CREATIVE 4D EXPRESS MONOGRAM WIZARD

Brand: Pfaff Pages: 2

Portal Server ETV v4.1

Brand: VBrick Systems Pages: 140

3CR15600 - Enterprise Management Suite

Brand: 3Com Pages: 218

Software Desktop Monitor

Brand: Intel Pages: 4

Application Update

Brand: TomTom Pages: 11

NAVIGATOR 380 -

Brand: Genius Pages: 26

SANsurfer FC HBA Manager Application

Brand: Qlogic Pages: 218

DIGITAL XBUS - SOFTWARE

Brand: Mackie Pages: 8

FLASHLITE2 ACTIONSCRIPT-LANGUAGE

Brand: MACROMEDIA Pages: 780

Brand: Xils lab Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands