manualshive.com logo in svg

Allied Telesis AT-S63, Features Manual

The Allied Telesis AT-S63 is a high-performance network switch that offers advanced features and seamless connectivity. For easy setup and configuration, download the free Cli User's Manual from our website manualshive.com. This comprehensive manual guides you through every aspect of the product, ensuring optimal performance and reliability.

Share
Download
background image

Chapter 29: Internet Protocol Version 4 Packet Routing

342

Section VII: Routing

Routing Interfaces and Management Features

Routing interfaces are primary intended for the IPv4 packet routing 
feature. There are, however, a number of management functions that rely 
on the presence of at least one routing interface on the switch to operate 
properly. The switch uses the IP address of an interface as its source 
address when performing the management function. The management 
functions are listed here:

ˆ

Accessing network servers

ˆ

Enhanced stacking

ˆ

Remote Telnet, SSH, and web browser management sessions

ˆ

Pinging a remote device

ˆ

Accessing DHCP or BOOTP servers

Accessing

Network Servers

A local subnet on the switch must have an interface if the device is using 
the subnet to access any of the following types of network servers:

ˆ

SNTP server for setting the switch’s date and time.

ˆ

RADIUS or authentication server for manager access 
accounts and 802.1x port-based network access control.

ˆ

Syslog server for storing events from the switch’s event logs.

ˆ

TFTP server for uploading and downloading files to the switch.

The switch uses the IP address of the interface as its source address 
when communicating with a network server. Without a routing interface on 
the subnet, the switch will not have a source IP address to include in its 
packets. For example, in order to set its date and time using an SNTP 
server, the switch must have a routing interface on the local subnet from 
where it is reaching the server.

The servers can be located on different routing interfaces on the switch. 
For instance, the switch can access an SNTP server through one interface 
and a RADIUS authentication server from another. This differs from some 
of the earlier versions of the AT-S63 Management Software where all the 
servers had to be members of what was referred to as the “management 
VLAN.”

If you intend to use the IPv4 routing feature of the switch and assign 
routing interfaces to all the local subnets and networks on a switch, this 
requirement should not be a issue. However, if you choose not to use the 
routing function and so not create interfaces or you have an AT-9400 
Switch that only supports one interface, some planning will be necessary 
in order to use these features. At a minimum, you must create one routing 
interface on the switch and plan your network so that the switch can 
access the servers from the subnet of the interface.

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

JETWAY MAGICTWINXP-R10 Software Install Manual preview
MAGICTWINXP-R10
Brand: JETWAY Pages: 43
Garmin Pilot User's Android User Manual preview
Pilot User's Android
Brand: Garmin Pages: 150
MAGIX VIDEO EASY3hd Manual preview
VIDEO EASY3hd
Brand: MAGIX Pages: 88
Arturia JUPITER-8V 2 User Manual preview
JUPITER-8V 2
Brand: Arturia Pages: 125
NeatWorks TV708LL/A - NeatWorks For Mac Using Manual preview
TV708LL/A - NeatWorks For Mac
Brand: NeatWorks Pages: 33
Blackberry TICKETMASTER - LEARN MORE User Manual preview
TICKETMASTER - LEARN MORE
Brand: Blackberry Pages: 7
FARONICS DEEP FREEZE - INTEGRATING WITH ALTIRIS... Manual preview
DEEP FREEZE - INTEGRATING WITH ALTIRIS...
Brand: FARONICS Pages: 22
Brother BT-1000 User Manual preview
BT-1000
Brand: Brother Pages: 22
Brother iPrint&Scan Manual preview
iPrint&Scan
Brand: Brother Pages: 115
Sony D-NF610 - Portable Cd Player Specifications preview
D-NF610 - Portable Cd Player
Brand: Sony Pages: 1
Sony D-NF420 - Portable Cd Player Specifications preview
D-NF420 - Portable Cd Player
Brand: Sony Pages: 2
Sony D-NE718CK - Portable Cd Player Specifications preview
D-NE718CK - Portable Cd Player
Brand: Sony Pages: 2
Sony D-NE520 - Atrac Cd Walkman Portable Player Specifications preview
D-NE520 - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 2
Sony CPF-IX001 - Wireless PC-Linked Audio System Installation Manual preview
CPF-IX001 - Wireless PC-Linked Audio System
Brand: Sony Pages: 2
Sony D-NE20 - Atrac Cd Walkman Installation & Operating Manual preview
D-NE20 - Atrac Cd Walkman
Brand: Sony Pages: 20
Sony D-NE718CK - Portable Cd Player Service Manual preview
D-NE718CK - Portable Cd Player
Brand: Sony Pages: 36
Sony D-NF420 - Portable Cd Player Service Manual preview
D-NF420 - Portable Cd Player
Brand: Sony Pages: 38
Sony D-NF610 - Portable Cd Player Operating Instructions Manual preview
D-NF610 - Portable Cd Player
Brand: Sony Pages: 40

Brands by name

Popular brands

Load more brands