Allied Telesis AT-S63 Features Manual Download Page 327 | Manualshive

Page: 327 / 538

background image

AT-S63 Management Software Features Guide

Section VII: Routing

327

Note

Routing interfaces can be configured from either the command line
interface or the menus interface.

The following subsections describe the three main components of a
routing interface:

VLAN ID (VID)

Interface number

IP address and subnet mask

VLAN ID (VID)

An interface must be assigned to the VLAN on the switch where its
network or subnet resides. The VLAN is identified by its VLAN
identification (VID) number or VLAN name. The sequence of operations is
to create the VLAN first and then the routing interface. Creating the
interface before the VLAN is not permitted.

A VLAN can have more than one interface in circumstances where a
virtual LAN contains more than one subnet. The maximum number is
sixteen routing interfaces per VLAN, making sixteen the maximum number
of subnets you can have in a VLAN and still support packet routing on all
of them.

Interface

Numbers

An interface must be assigned an interface number in the range of 0 to 15.
This range corresponds to the maximum number of interfaces permitted in
a VLAN. Interfaces in different VLANs on the same switch can have the
same interface number, but interfaces in the same VLAN must have
different numbers.

For instance, if a switch has four local subnets and each is in a different
VLAN, all of the interfaces could have the same interface number, such as
0. However, if two or more of the subnets reside in the same VLAN, the
routing interfaces for the subnets in the VLAN must be assigned different
interface numbers.

Interfaces numbers are only used for interface identification when there is
more than one subnet and routing interface in a VLAN. Consequently, the
sequence in which the interface numbers are used is not important.

IP Address and

Subnet Mask

An interface must be a member of the local network or subnet where it will
function as the logical connection for routing IPv4 packets. As such, it
must be assigned a unique IP address and a subnet mask appropriate to
the network or subnet.

The IP address and subnet mask of an interface can be assigned
manually or supplied by a DHCP or BOOTP server on the network. When
a VLAN contains more than one interface, only one of the interfaces can
obtain its IP address from a DHCP or BOOTP server. The IP addresses of

«
...
325
326
327
328
329
...
»

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

Brand: NEC Pages: 3

Brand: TANDBERG Pages: 66

Content Server None

Brand: TANDBERG Pages: 14

HXDU010EB - Story Station 1 TB External Hard...

Brand: Samsung Pages: 7

AV Tutor MCFBV1-D

Brand: Califone Pages: 1

MetaFrame MetaFrame Presentation Server

Brand: Citrix Pages: 97

ANTI-VIRUS - FOR FREEBSD-OPENBSD-BSDI MAIL SERVER

Brand: KAPERSKY Pages: 295

12812-051462-9011 - 3DS MAX 9 COM LEGACY SLM

Brand: Autodesk Pages: 2577

Brand: FARONICS Pages: 43

CERTIFICATE 8.0 RELEASE NOTES

Brand: Red Hat Pages: 34

Brand: JETWAY Pages: 43

Brand: I.R.I.S. Pages: 10

IRISPOWERSCAN 9.0

Brand: I.R.I.S. Pages: 153

Topo North America 9.0

Brand: DeLorme Pages: 257

Brand: FieldServer Pages: 29

Brand: Mackie Pages: 12

Brand: CAERE Pages: 108

DIRECTOR MX 2004-DIRECTOR SCRIPTING

Brand: MACROMEDIA Pages: 1130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands