Allied Telesis AT-S63 Features Manual Download Page 299 | Manualshive

Page: 299 / 538

background image

AT-S63 Management Software Features Guide

Section VI: Virtual LANs

299

This highly segmented configuration is useful in situations where traffic
generated by each end node or network segment connected to a port on
the switch needs to be kept separate from all other network traffic, while
still allowing access to an uplink to a WAN. Unicast traffic received by the
uplink port is effectively directed to the appropriate port and end node and
is not directed to any other port on the switch.

The 802.1Q Multiple VLAN configuration is appropriate when the device
connected to the uplink port is IEEE 802.1Q compatible, meaning that it
can handle tagged packets.

When you select the 802.1Q-compliant VLAN mode, you are asked to
specify the uplink VLAN port. You can specify only one uplink port. The
switch automatically configures the ports into the separate VLANs.

Note

The uplink VLAN is the management VLAN. Any remote
management of the switch must be made through the uplink VLAN.

Client_VLAN_10

10

10

22

Client_VLAN_11

11

11

22

Client_VLAN_12

12

12

22

Client_VLAN_13

13

13

22

Client_VLAN_14

14

14

22

Client_VLAN_15

15

15

22

Client_VLAN_16

16

16

22

Client_VLAN_17

17

17

22

Client_VLAN_18

18

18

22

Client_VLAN_19

19

19

22

Client_VLAN_20

20

20

22

Client_VLAN_21

21

21

22

Uplink_VLAN

22

22

Client_VLAN_23

23

23

22

Client_VLAN_24

24

24

22

Table 84. 802.1Q-Compliant Multiple VLAN Example (Continued)

VLAN Name

VID

Untagged Port

Tagged Port

«
...
297
298
299
300
301
...
»

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

Brand: NEC Pages: 3

Venture IP Telephone System

Brand: Aastra Pages: 10

Content Database Editor v 1.0

Brand: AMX Pages: 28

Brand: Sun Microsystems Pages: 38

Brand: Brady Pages: 33

Brand: Ulead Pages: 168

Brand: GRASS VALLEY Pages: 2

Brand: GRASS VALLEY Pages: 24

AURORA INGEST - S AND UPGRADE INSTRUCTIONS V7.1

Brand: GRASS VALLEY Pages: 66

Brand: Magellan Pages: 14

Brand: JDS Uniphase Pages: 2

Brand: DataCard Pages: 2

Media Manager for PSP

Brand: GameShark Pages: 15

magicolor 2590MF

Brand: 3D Nord Pages: 198

ThinkCentre A61e

Brand: Lenovo Pages: 4

ThinkCentre A62

Brand: Lenovo Pages: 134

ThinkCentre A63

Brand: Lenovo Pages: 216

ThinkCentre A62

Brand: Lenovo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands