Allied Telesis AT-S63 Features Manual Download Page 293 | Manualshive

Page: 293 / 538

background image

AT-S63 Management Software Features Guide

Section VI: Virtual LANs

293

Figure 38. GID Architecture

GARP registers and deregisters

attribute

values through GARP messages

sent at the GID level. A GARP participant that wishes to make a
declaration (an applicant registering an

attribute

value) sends a JoinIn or

JoinEmpty message. An applicant that wishes to withdraw a declaration
(deregistering an

attribute

value) sends a LeaveEmpty or LeaveIn

message. Following the de-registration of an

attribute

value, the applicant

sends a number of Empty messages. The purpose of the Empty message
is to prompt other applicants to send JoinIn/JoinEmpty messages. For the
GARP protocol to be resilient against multiple lost messages, a LeaveAll
message is available. Timers are used in the state machines to generate
events and control state transitions.

The job of the applicant is twofold:

To ensure that this participant’s declarations are registered by other
participants’ registrars

To ensure that other participants have a chance to redeclare (rejoin)
after anyone withdraws a declaration (leaves).

The applicant is therefore looking after the interests of all would-be
participants. This allows the registrar to be very simple.

The job of the registrar is to record whether an attribute is registered, in the
process of being deregistered, or is not registered for an instance of GID.

Attribute ... state:

Attribute C state:

Attribute A state:

Applicant
State

Registrar
State

Attribute B state:

GID

«
...
291
292
293
294
295
...
»

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

COOL 3D-PLUG-IN MADNESS II

Brand: Ulead Pages: 10

BREEZE-MANAGING EXTERNAL BREEZE REPORTS

Brand: MACROMEDIA Pages: 18

Brand: Paradyne Pages: 24

Brand: TC Electronic Pages: 22

drivers for video card

Brand: EVGA Pages: 23

Brand: Extron electronics Pages: 37

TWIG CONFIGURATOR

Brand: Benefon Pages: 28

Brand: Intel Pages: 19

Brand: MINOLTA-QMS Pages: 42

ZVM - FOR LINUX V6 RELEASE 1

Brand: IBM Pages: 172

DEEP FREEZE ENTERPRISE - TREND MICRO OFFICESCAN...

Brand: FARONICS Pages: 17

010-10844-00 - Mobile XT - GPS Software

Brand: Garmin Pages: 8

Brand: iHome Pages: 22

Brand: Guzik Pages: 29

Brand: Hitachi Pages: 248

Wide Format 6030

Brand: Xerox Pages: 20

Display Manager

Brand: Sharp Pages: 28

Brand: Omron Pages: 115

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands