Allied Telesis AT-S63 Features Manual Download Page 72 | Manualshive

Page: 72 / 538

background image

Chapter 2: AT-9400Ts Stacks

72

Section I: Basic Operations

If the switch determines that its ID number is set to STATIC with the
value 1, then it knows that it’s the master switch of the stack and that it
is responsible for maintaining the STACK.CFG file for the entire stack.

If the switch determines that its ID number is set to STATIC with a
value of 2 or more, then it knows that it is part of a stack and that it
should receive its configure settings from the master switch.

If the switch’s ID number is set to STATIC but the device is not a part
of a stack, the switch still uses the STACK.CFG file to set its
parameter settings. If the switch does not have this file, it uses the
default values for its parameter settings.

By having two standard configuration files, a switch can retain its prior
configuration settings when converted from a stand-alone configuration to
a stack member, or vice versa. This saves you the trouble of having to
reconfigure the device.

Since there are two different configuration files, the parameter settings
from a stand-alone configuration file cannot be automatically transferred to
a stack configuration file. For a switch to have the same settings in a stack
that it had as a stand-alone device, you must reapply the settings after
adding the switch to the stack.

«
...
70
71
72
73
74
...
»

Summary of Contents for AT-S63



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-S63

ZENworks 7.2 Linux Management

Brand: Novell Pages: 10

Brand: Adobe Pages: 306

DATA SYNCHRONIZER

Brand: Novell Pages: 50

Brand: PNY Pages: 15

Brand: Black Box Pages: 65

Writing an embedded application loader

Brand: Sierra Wireless Pages: 9

Brand: Sierra Wireless Pages: 16

Brand: Mad Catz Pages: 12

ADAPTIVE SERVER IQ 12.4.0

Brand: Sybase Pages: 52

DEEP FREEZE - SMS INTEGRATION 8-2006

Brand: FARONICS Pages: 10

Plug-in for Vocals and Monophonic

Brand: Waves Pages: 20

magicolor 2590MF

Brand: 3D Nord Pages: 198

Stylus pro 3800 portrait edition

Brand: Epson Pages: 12

Stylus Pro 5500

Brand: Epson Pages: 2

Stylus Pro 4800 Portrait Edition

Brand: Epson Pages: 6

Stylus Pro 4800 Portrait Edition

Brand: Epson Pages: 396

Stylus Pro 7600

Brand: Epson Pages: 5

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands